What Affects the Cost of a Panel Upgrade in New Jersey
Updated November 2026
The cost of a panel upgrade in New Jersey depends mostly on the service size you need, how much of the service equipment outside the house has to change, what the code and the power company require at your address, and the condition of the wiring around the panel.
This page explains the factors only. It has no price ranges, because two houses on the same street can need very different work. For a written price on your home, book a free estimate visit. To see what a standard job includes, read our 200 amp panel upgrade page.
Which factors change the price the most?
| Factor | Why it matters |
|---|---|
| Service size (100, 150, 200 or 300 amp) | Bigger services need larger equipment and larger service conductors. |
| Meter socket and service entrance cable | If the meter socket or the cable from the meter to the panel must be replaced, the job grows. |
| Panel location or relocation | Keeping the panel where it is costs less than moving it. |
| Grounding and bonding | Older homes often need grounding and bonding brought up to current code. |
| Circuit count | Every circuit has to be moved, labeled and checked in the new panel. |
| Permits and inspection | Required for every panel upgrade in New Jersey. |
| Power company coordination | The utility must disconnect, approve and reconnect the service. |
| Meter, underground service or mast changes | Sometimes the utility requires the meter to move or the service drop or mast to change. |
| Old panels (Federal Pacific, Zinsco) | These often come with older wiring problems that show up once the cover is off. |
| New loads like an EV charger | Added load can push you to a larger service size. |
How does service size affect cost?
Many older homes have 100 or 150 amp service. 200 amps is a common upgrade size. Larger homes, or homes adding big loads, may need 300 amps or a sub panel or 300 amp service. Larger service means a larger panel, a larger meter socket and larger conductors. Breaker and wire sizing follow the code. Our breaker sizing guide explains how that works.
Does the meter socket or service cable need to change?
Often, yes. If you increase the service size, the meter socket and the service entrance cable usually must be rated for the new size. For PSE&G upgrades of 200 amps or less, the contractor picks up a meter pan at a location PSE&G names, bringing the original town permit and the PSE&G project number. Corroded or damaged outdoor equipment also has to be replaced, even on a same-size swap.
What if the panel has to move?
A panel that stays in the same spot is the simplest job. Moving it adds new cable runs, and every existing circuit has to reach the new location. Panels in closets, bathrooms or other spots without proper working space often have to move. Your local inspector decides what is acceptable.
Why do grounding and bonding come up?
A new service has to meet the grounding and bonding rules in force when the permit is issued. Many older New Jersey homes have a grounding electrode system or water pipe bond that does not meet current code. Bringing it up to code adds labor and material. See our grounding and bonding guide for the basics.
What does the current code add to a service upgrade?
New Jersey enforces the 2023 National Electrical Code under N.J.A.C. 5:23-3.16, effective August 17, 2026. Complete permit applications filed through February 17, 2027 may still use the 2020 NEC. Two rules often affect a service upgrade:
- Surge protection. The NEC requires a surge-protective device for dwelling services, and the 2023 edition applies it when service equipment is replaced.
- Outdoor emergency disconnect. Since the 2020 NEC, a new or replaced service on a one- or two-family dwelling needs an emergency disconnect in a readily accessible outdoor location so first responders can shut off power.
The local inspector has the final say on what applies to your job. Our NJ electrical code library covers more of these rules, and our GFCI and AFCI page explains protection that may be required on some circuits.
How do circuit count and existing wiring affect cost?
Each circuit has to be moved to the new panel, connected to the right breaker and labeled. More circuits means more time. Short, damaged or undersized wires found at the panel may need extending or repair.
What about permits and inspection?
Electrical work in New Jersey needs a permit from your town's construction office, and the work is inspected. We pull the permit in our name on every job. After the inspection passes, the town issues the approval the power company needs before it will connect the new service. Permit fees are set by each town.
What does the power company have to do?
The utility has to approve the upgrade, disconnect the old service and reconnect the new one. PSE&G requires an application with load details and a passed local inspection (a Certificate of Approval, or "cut-in card") before it installs the meter. PSE&G says residential requests may take up to six weeks, depending on permits and inspections, so scheduling affects the timeline.
Will the meter, mast or underground service have to change?
Sometimes. The utility may require the meter to move, a new mast or weatherhead for an overhead service, or changes to an underground service. Underground work may involve trenching and burial depths set by code. See our underground wire depth guide. The estimate visit is a good time to ask whether any of this applies to your home.
What about walls and ceilings?
If walls or ceilings have to be opened to run cable or move a panel, patching and painting are usually done by a separate trade. Ask about it at your estimate visit.
Do Federal Pacific or Zinsco panels cost more to replace?
The panel swap itself is similar. The difference is what is found. Older panels often have heat damage, loose connections or older wiring around them. The CPSC closed its 1983 investigation of Federal Pacific Stab-Lok breakers without making a determination about their safety. Its testing found the breakers failed some UL calibration tests. It advises finding out why a breaker trips and consulting a licensed electrician instead of just resetting it. Read more on our Federal Pacific panel replacement page.
Does adding an EV charger change the cost?
It can. An EV charger is a large continuous load. A load calculation shows whether your current service can carry it. If not, the charger and the service upgrade are often done together. See home EV charger installation and our EV charger page. We also do panel upgrades for solar-ready homes, but we do not install solar panels.
How Gareffa Electric can help
Gareffa Electric is a family-owned, licensed New Jersey electrical contractor (NJ Electrical Contractor License #18578) based in Nutley. We carry $2M liability insurance, and a bond is available on request. We serve Bergen, Hudson, Essex and Passaic counties.
- Panel and service upgrades from 100A to 4000A, including 200A and 300A.
- Sub panels and replacement of Federal Pacific and Zinsco panels.
- Every job is permitted in our name and done by licensed electricians on our crew.
- Book a free estimate visit for a written price.
If you have a problem now, such as a breaker that keeps tripping, book a $150 scheduled service call or a $350 same-day service call. Same-day or next-day dispatch is available, and we are often there within 2 to 4 hours of booking. See our electrical repair page or home electrical safety check. Electrical work in New Jersey needs a permit and a licensed electrician, so please do not try a panel upgrade yourself. If there is smoke, fire or sparking that will not stop, leave the house and call 911.
FAQ
Why can't you give a price over the phone?
The price depends on the meter, service cable, grounding, panel location and what the utility requires at your address. We need to see those things to write an accurate price.
What does the free estimate visit include?
We look at your panel, meter and service, and then give you a written price for the work.
Do I need a permit to upgrade my panel in New Jersey?
Yes. A panel upgrade needs a permit and an inspection. We pull the permit in our name. The local inspector has the final say.
Will my power be off during the upgrade?
Yes, for part of the job. The power company disconnects the service and reconnects it after the work is inspected and approved.
Can I add a surge protector at the same time?
Yes. Under the 2023 NEC, a surge-protective device is required when dwelling service equipment is replaced, so on most upgrades it is part of the job. The local inspector has the final say.
Who patches the walls after a panel upgrade?
If walls or ceilings have to be opened, patching and painting are usually done by a separate trade. Ask about it at your estimate visit.
Do I need a bigger service for an EV charger?
Not always. A load calculation shows whether your current service can handle the charger.
Call Gareffa Electric at (973) 662-4333. We are open Monday to Saturday, 7 AM to 6 PM, closed Sunday.