Electrical Grounding and Bonding in New Jersey Homes
Grounding connects your electrical system to the earth, and bonding ties all the metal parts together so a fault trips the breaker fast. In New Jersey, both are set by Article 250 of the 2023 National Electrical Code (NEC 2023), which the state now enforces.
This page explains the parts of a home grounding system in plain terms. It is not a how-to guide. Electrical work in New Jersey needs a permit and a licensed electrician, and the local inspector has the final say.
Which code applies to grounding in New Jersey?
New Jersey adopted NEC 2023 as its electrical subcode (N.J.A.C. 5:23-3.16), effective August 17, 2026. There is a grace period: a complete permit application filed through February 17, 2027 may still use NEC 2020 if it says so. From February 18, 2027, only NEC 2023 applies. All section numbers below are from NEC 2023.
What is the difference between grounding and bonding?
Grounding is a connection to the earth. Under NEC 2023 Section 250.4(A), grounding the electrical system limits voltage from lightning, utility surges, or accidental contact with higher-voltage lines, and keeps the voltage steady during normal use.
Bonding connects metal parts to each other and back to the source. Section 250.4(A) says bonding creates an effective ground-fault current path. That low-resistance path lets enough current flow during a fault for the breaker to trip.
The key point: the earth alone does not clear a fault. NEC 2023 Section 250.4(A)(5) says the earth is not an effective ground-fault current path. Bonding is what carries fault current back so the breaker trips. A home needs both.
What is the grounding electrode system?
A grounding electrode is the part that actually touches the earth. Section 250.50 requires every qualifying electrode present at a building to be bonded together into one system. You do not pick one and ignore the others. There is one exception (250.50 Exception): footing rebar in an existing building does not have to be added if it cannot be reached without disturbing the concrete.
| Electrode | NEC 2023 section | Minimum to qualify |
|---|---|---|
| Metal underground water pipe | 250.52(A)(1) | 10 ft or more in direct contact with the earth |
| Concrete-encased electrode ("Ufer") | 250.52(A)(3) | 20 ft of rebar at least 1/2 in. diameter, or 20 ft of bare copper no smaller than 4 AWG, in at least 2 in. of concrete |
| Ground ring | 250.52(A)(4) | 20 ft of bare copper no smaller than 2 AWG |
| Rod or pipe electrode | 250.52(A)(5), 250.53(A)(4) | At least 8 ft long (250.52(A)(5)), installed with 8 ft in contact with soil (250.53(A)(4)); rods at least 5/8 in. diameter unless listed |
| Metal underground gas piping | 250.52(B) | Not permitted as an electrode |
Ground rods
Many homes use one or two ground rods, often alongside a metal water pipe. Under Section 250.53(A)(2), a single rod must have a second (supplemental) electrode unless the single rod measures 25 ohms or less to earth. Section 250.53(A)(3) requires the second rod to be at least 6 ft from the first. Two rods are common because proving 25 ohms takes a test.
Water pipe electrode
A metal water service pipe in the ground can be an electrode. But Section 250.53(D)(2) says it must always be backed up by another electrode, such as a rod. The reason is simple: if the water company or a plumber swaps the pipe for plastic, the house would lose its only electrode. Section 250.53(D)(1) also requires the grounding path not to depend on the water meter or filters, so jumpers go around them.
Concrete-encased (Ufer) electrode
A Ufer uses the steel rebar or copper wire in a building footing. A DCA bulletin (02-2) notes that studies rate it among the most reliable electrodes. In new construction, where the footing rebar meets the size rules, it must be bonded in, and the building subcode inspector checks the connection before the concrete is poured. The bulletin notes this does not apply to electrical work in an existing structure.
What is the grounding electrode conductor?
The grounding electrode conductor (GEC) is the wire from your service to the electrodes. Section 250.24(A)(1) covers where it connects to the grounded (neutral) service conductor. Its size usually follows Table 250.66, based on the size of the service wires, with two common limits:
- To a rod or pipe electrode only: never required to be larger than 6 AWG copper (Section 250.66(A)).
- To a concrete-encased electrode only: never required to be larger than 4 AWG copper (Section 250.66(B)).
What does the main bonding jumper do?
At the service disconnect, usually your main panel, the neutral bar and the metal enclosure are tied together by the main bonding jumper. Section 250.24(C) requires it, and Section 250.28 covers what it is made of and how it is sized. In many panels it is a green screw or a metal strap.
This is the one spot where neutral and ground meet. During a fault, current travels on the ground wires back to this point, onto the neutral, and back to the utility. That is what trips the breaker.
Why do subpanels keep neutral and ground separate?
Section 250.24(B) prohibits connecting the neutral to ground on the load side of the service disconnect. So in a subpanel, the neutrals land on an isolated neutral bar, and the ground wires land on a separate bar bonded to the box. No bonding screw goes in.
If neutral and ground are tied together in a subpanel, normal neutral current can flow on metal boxes, conduit, and ground wires. That current should not be there. It can shock someone and can make troubleshooting hard. This is a common finding when we add a subpanel or check a panel someone else installed.
What are the signs of a grounding problem?
- Three-prong outlets on two-wire circuits. Many older homes in Bergen, Hudson, Essex and Passaic counties have three-prong outlets with no ground wire behind them.
- A plug-in outlet tester shows "open ground."
- A tingle when touching an appliance, a faucet, or a metal fixture.
- No visible ground wire from the panel to a rod or water pipe, or a cut or loose clamp.
- Water service replaced with plastic and no rod added.
- A subpanel with neutral and ground on the same bar.
Is a three-prong outlet with no ground allowed?
Not as a plain three-prong outlet. When an outlet box has no ground wire, Section 406.4(D)(2) allows three replacement options: a two-prong outlet; a GFCI outlet marked "No Equipment Ground"; or a three-prong outlet protected by an upstream GFCI and marked both "GFCI Protected" and "No Equipment Ground." GFCI protection improves shock safety, but it does not add a ground. Some appliances and electronics still need a real ground wire.
When should you call an electrician?
Call a licensed electrician if you see any sign above, if you are buying an older home, or before a panel upgrade, subpanel, or EV charger. Grounding work happens at the service and inside the panel, where the utility conductors stay live. It is not a DIY job, and in New Jersey it needs a permit and an inspection.
How Gareffa Electric can help
Gareffa Electric is a family-owned, licensed New Jersey electrical contractor (NJ Electrical Contractor License #18578), with $2M liability insurance. We are based in Nutley and serve Bergen, Hudson, Essex and Passaic counties. Every job is permitted in our name.
- A home electrical inspection checks your electrodes, grounding conductor, main bonding jumper, and outlets.
- We handle electrical repairs such as adding a missing rod, fixing a bad clamp, or correcting a subpanel.
- Book a free estimate visit at /products/estimate, or a $150 service call at /products/estimate-visit.
More code topics are in our New Jersey electrical code library and our electrician FAQ.
Frequently asked questions
What is the proper way to ground an electrical panel?
Under NEC 2023, the service panel connects to every qualifying electrode on the property, bonded together into one system (Section 250.50). One exception: footing rebar in an existing building does not have to be added if it cannot be reached without disturbing the concrete. A grounding electrode conductor runs to the electrodes, and the main bonding jumper ties neutral to the enclosure at the service only (Sections 250.24(C) and 250.28). A licensed electrician must do this under a permit.
How many ground rods does a New Jersey house need?
One rod is enough only if it measures 25 ohms or less to earth (Section 250.53(A)(2)). Otherwise a second electrode is required. If the second electrode is another rod, pipe or plate, it must be at least 6 ft from the first (Section 250.53(A)(3)). The local inspector decides what passes.
Can my water pipe be my only ground?
No. Section 250.53(D)(2) requires a metal water pipe electrode to be backed up by another electrode, such as a rod.
Why is there no green bonding screw in my subpanel?
Because Section 250.24(B) prohibits a neutral-to-ground connection after the service disconnect. Neutral and ground must stay on separate bars in a subpanel.
Is a GFCI outlet the same as a grounded outlet?
No. Section 406.4(D)(2) allows a GFCI as a replacement where there is no ground wire, but it must be marked "No Equipment Ground." It protects people from shock but does not provide a ground.
Can gas piping be used as a ground?
No. Section 250.52(B) does not permit metal underground gas piping as a grounding electrode.
Do I need a permit to fix grounding in New Jersey?
Yes. Electrical work in New Jersey needs a permit and a licensed electrician, and the local inspector has the final say.
Questions about grounding in your home? Call Gareffa Electric at (973) 662-4333, Monday to Saturday, 7 AM to 6 PM. Closed Sunday.