EV Charger Circuit Requirements in New Jersey (NEC Article 625)
Short answer: Under NEC 2023 Article 625, a home Level 2 charger is a continuous load. It needs its own branch circuit, and its breaker must be at least 125% of the charger's current rating. A 32-amp charger needs at least a 40-amp breaker, a 40-amp charger needs at least 50 amps, and a 48-amp charger needs at least 60 amps.
This page is part of our New Jersey electrical code library. It explains the rules in plain terms. It is not a do-it-yourself guide. In New Jersey, adding a charger circuit needs a permit and an inspection, and the local inspector has the final say.
Which code applies in New Jersey right now?
New Jersey adopted the 2023 National Electrical Code (NFPA 70) under the electrical subcode, N.J.A.C. 5:23-3.16, as of August 17, 2026. There is a six-month grace period. A complete permit application with all prior approvals, submitted by February 17, 2027, can still be reviewed under the previous code, which was NEC 2020. The section numbers below are from NEC 2023.
Does an EV charger need a dedicated circuit? (625.40)
Yes, for a Level 2 charger. NEC 2023 requires an individual branch circuit for EV supply equipment rated more than 16 amps or more than 120 volts. An individual branch circuit feeds only that one piece of equipment. Level 2 home chargers run on 240 volts, so they need their own circuit.
There is one exception. One branch circuit may feed more than one charger when the load is controlled by an energy management system or by adjustable charger settings under 625.42.
How do you size the breaker for an EV charger? (625.41 and 625.42)
The code treats an EV charger as a continuous load (625.42). It assumes the charger can run at full output for hours. Overcurrent protection must be at least 125% of the charger's current rating (625.41). The conductors also have to carry at least 125% of the rating.
| Charger output setting | 125% of rating | Minimum breaker size |
|---|---|---|
| 16 A | 20 A | 20 A |
| 24 A | 30 A | 30 A |
| 32 A | 40 A | 40 A |
| 40 A | 50 A | 50 A |
| 48 A | 60 A | 60 A |
Wire size depends on more than amps. Cable type, terminal temperature ratings and the length of the run all matter. For example, a 2023 NEC study guide shows a 40-amp charger needing a 50-amp circuit. That works out to 8 AWG conductors rated at 75°C, or 6 AWG if you use NM cable. Your electrician and inspector will confirm the exact wire size for your job. For more on matching breakers to wire, see our breaker sizing guide.
What about chargers with adjustable settings?
Many hardwired chargers let the installer set a lower output. Under 625.42(B), the adjusted setting has to appear on the rating label. Adjustable settings are allowed only on fixed-in-place equipment. Access to the setting must be restricted, for example with a tool-operated cover or password-protected commissioning software. The circuit is then sized to the setting. This is a job for your electrician, not the homeowner.
Does an EV charger need GFCI protection? (625.54)
If the charger plugs into a receptacle, yes. NEC 2023 requires GFCI protection for all receptacles installed to connect EV supply equipment. That covers plug-in chargers on a 240-volt outlet in a garage or driveway. Other GFCI rules in Article 210 can also apply depending on location. See our GFCI and AFCI requirements page. Ask your inspector if you are unsure.
Does a home charger need a separate disconnect? (625.43)
For most home units, no. A separate disconnect is required when the equipment is rated more than 60 amps or more than 150 volts to ground. That disconnect must be readily accessible and lockable in the open position. If the disconnect is not next to the charger, a plaque on the charger must show where it is. Most home Level 2 chargers are rated 48 amps or less on a 240-volt system, so this rule often does not apply. Larger units may need a disconnect.
Will my panel handle an EV charger?
A charger is often the biggest load in the house. Before adding one, a load calculation checks whether the service can carry it. NEC 2023 section 220.57 says to count EV supply equipment at 7,200 VA or the nameplate rating, whichever is larger.
If the numbers do not work, you have two main options:
- Load management (EVEMS). Under 625.42(A) and Article 750, an energy management system can control the charger. The service and feeders are then sized to the maximum the system allows. This can sometimes avoid a service upgrade.
- Service upgrade. Many older homes need more capacity. See our 200-amp panel upgrade page and our sub panel and 300-amp service page.
If your home has a Federal Pacific or Zinsco panel, have it looked at before adding a big new load. See Federal Pacific panel replacement. If the charger goes in a detached garage or on a post, the trench depth rules on our underground wire depth page apply.
Do you need a permit for an EV charger in New Jersey?
Yes, in most cases. The NJ Department of Community Affairs classifies a charging system that needs a new 120- or 240-volt outlet, or a line wired directly to the charger, as minor work under N.J.A.C. 5:23-2.17A. A permit and an inspection are required. Your electrical contractor notifies the local code office before work begins and files the permit application within five business days. The local code office must inspect within three business days of your request, unless you and the office agree on another time within 30 days.
Swapping an outlet that is already sized correctly for one with a matching plug shape is ordinary maintenance and needs no permit. It should still be done by a licensed electrician, and a 240-volt receptacle for an EV charger needs GFCI protection under 625.54.
Local construction offices often ask for a load calculation and the charger's spec sheet with the application. Freestanding chargers may also need zoning review in some towns.
Safety note: If you see smoke, fire or sparking that will not stop, leave the building and call 911.
How Gareffa Electric can help
Gareffa Electric is a family-owned, licensed New Jersey electrical contractor, NJ Electrical Contractor License #18578. We carry $2M in liability insurance, and a bond is available on request. We are based in Nutley and serve Bergen, Hudson, Essex and Passaic counties.
- Home and commercial EV charger installs, including Tesla wall chargers. See home EV charger installation and EV chargers.
- Load calculations, load management setup and panel or service upgrades from 100A to 4000A.
- Experience with New Jersey utility EV charger rebate paperwork.
- Every job is permitted in our name and done by licensed electricians on our crew.
Book a free estimate visit to plan a charger install. For a problem with an existing circuit, book a $150 scheduled service call, which includes the diagnostic and first hour; the fee is credited on jobs over $1,500. Need someone today? Book a $350 same-day service call. Same-day or next-day dispatch is available, and we are often there within 2 to 4 hours of booking. More answers are on our electrician FAQ.
FAQ
What size breaker do I need for a 48-amp EV charger?
At least a 60-amp breaker. The code requires 125% of the charger's rating, and 48 times 1.25 is 60.
Can I put a 40-amp charger on a 40-amp breaker?
No. A 40-amp charger needs at least a 50-amp breaker under NEC 625.41. Your electrician can set an adjustable charger to 32 amps for a 40-amp circuit, if the setting is on the rating label and access to it is restricted.
Does a hardwired charger need GFCI protection?
The NEC 2023 GFCI rule in 625.54 covers receptacles for EV chargers. Other code sections can apply based on location. Your inspector decides.
Can two chargers share one circuit?
Yes, if an energy management system or adjustable settings limit the total load under 625.42. Otherwise each Level 2 charger needs its own circuit.
Do I need to upgrade my panel for an EV charger?
Not always. A load calculation counts the charger at 7,200 VA or its nameplate rating, whichever is larger. If the service is too small, load management or an upgrade can solve it.
Is an EV charger permit required in New Jersey?
Yes, when a new outlet or circuit is installed or the charger is wired directly. It is classed as minor work, so work can start after your electrician notifies the local code office, and an inspection follows.
Which NEC edition does my town use?
New Jersey adopted NEC 2023 as of August 17, 2026. Complete applications submitted by February 17, 2027 may still be reviewed under NEC 2020.
Call Gareffa Electric at (973) 662-4333. We are open Monday through Saturday, 7 AM to 6 PM, and closed Sunday.